Extra 330Lx – 103″ (2,60m)

Pilot-Rc Extra’s are known for flying great, regardless of the version.  This new highly carbon reinforced version takes the design further than ever before.  Stronger, more rigid and also lighter than ever before, this alone makes this plane a winner, but add the design tweaks and it becomes a showstopper!


Model:Extra 330Lx – 35%
Wingspan:103″ (2.610mm)
Length:101″ (2.576mm)
Wing area:2,156 “² (13,910 cm²)
Weight:27.8lbs (12.6kg)

Video and GALLERY:


  • NEW! Full Carbon reinforced fuselage and wing using carbon laminated wood and carbon stringers.  
  • NEW! Updated design with a shorter wingspan, offering a faster roll rate and even more agile than ever before.
  • Choose between a fully printed cover design, or classic Genuine German Oracover (Ultracote) covering
  • Highly prefabricated, experienced builders can have air ready in under a day
  • Pre-installed hinges (glued and pinned)
  • Internally mounted cowling – so no external screws exposed
  • Exhaust tunnel pre-installed in fuselage for easy canister installation
  • Removable rudder (as well as removable wings and stabs)
  • Laser engraved motor mounting position 
  • Push-Pull system for Rudder servos

Included hardware:

  • Complete air frame with all basic accessories (such as carbon fibre main undercarriage, tail-gear assembly and wing-tubes as well as fibreglass control horns and wheel pants)
  • Pre-installed hinges and pre-mounted canopy
  • Fuel tank and fuel tubing pre-prepared, fuel dot and breather valve
  • Wheels, axels and wheel pants
  • Pre-prepared pull-pull wires and pushrods with ball links
  • Matching carbon spinner

Required hardware:

Motor: 80-120cc or equivalent electric

Servos: 7-8 high torque (minimum 20kg) plus throttle // Uses x2 per aileron, x1 per elevator and x1 or x2 on rudder

Also requires all the usual accessories such as transmitter, receiver, propeller, batteries, powerbox, extension leads and possibly other small accessories.

Pilot-Rc recommended hardware:

Colour schemes available:

Colour scheme LX-01: 
References: Oracover 21-010, 21-022, 21-033, 21-091, 21-071 / Ultracote HANU870, HANU883, HANU872, HANU881, HANU874.

Colour scheme LX-02: 
References: Oracover 21-010, 21-050, 21-033, 21-091, 21-071 / Ultracote HANU870, HANU873, HANU872, HANU881, HANU874.

Colour scheme LX-03: 
Oracover and decal scheme


Colour scheme LX-04: 
Oracover and decal scheme


Colour scheme LX-05: 
Oracover and decal scheme

Colour scheme LX-06: 
Oracover and decal scheme

Colour scheme LX-07: 
References: Oracover 21-023, 21-071, 21-010 / Ultracote HANU866, HANU874, HANU870

Colour scheme LX-08: 
References: Oracover 21-050, 21-071, 21-010 / Ultracote HANU873, HANU874, HANU870

Colour scheme LX-09: 
References: Oracover 21-043, 21-071, 21-010 / Ultracote HANU903, HANU874, HANU870

Colour scheme LX-10: 
References: Oracover 21-023, 21-033, 21-071 / Ultracote HANU866, HANU872, HANU874

Build information


A: 357mm – B: 343mm – C: 302mm – D: 325mm


A: 390mm – B: 127mm – C: 448mm – D: 120mm – E: 172mm – F: mm


A: – B: – C: 81mm – D: – E: 8.5mm

Extension wire lengths:


Each aileron:
30m + 83cm
(nearest servo and furthest servo – to reach receiver direct)

Each elevator:

(when using direct – if installing pull pull, no required extension)


Measured back from leading edge of the wing at the fuselage.

You will find a laser engraved C.G. emblem on the inside of the fuselage, located close to the wing tube, which also shows the exact location for Center of Gravity.

FULL Build manual: