Following the great success and feedback from our large FC1, we have continued our collaboration with Ralph & Enrico from Elster Jet to produce a smaller, more everyday and convenient version, middle sized on best 3D performance.
Specifications:
| Model: | FC1 |
| Wingspan: | 65.4″ (1,662mm) |
| Length: | 106.6″ (2,709mm) |
| Wing area: | – – |
| Weight: | 27.7lbs (12.6kg) with JetCat P220Rxi turbine and fuel bag |
Video:
GALLERY:
FEATURES:
- German design, by Ralph and Enrico from Elster Jet
- New Quick Release wing and stabilizer
- Extremely lightweight full composite construction especially designed for outstanding 3D performance
- Painted outside the mold so no seam lines
- Ultra strong and light weight landing gear mounts, with factory installed blind nuts so mounting is just plug and play
- Specially designed easy access to turbine for speedy installation
- Field setup can be done in seconds, thanks to the quick releases on the wings without the need for any tools, and the single elevator bolt accessed from the side
- Removable wing and elevator for easy transport
Please note that the FC1 is designed specifically for aerobatics and 3D vectored flight, with light weight being key. It is not designed to be used as a full power, high speed race plane.
Included hardware:
- Complete air frame (including carbon wing-tubes and preinstalled and painted fibreglass control horns)
- Servo extension leads
- Vector thrust pipe
- 3.600ml fuel tank (optional upgrade to fuel bag)
- 250ml UAT tank
- Pre-prepared pushrods with ball links
Also available: Full retract combo. Includes Pilot-RC electric retracts and electric brakes, specific for this model.
Also available: Turbine Ready version. Includes all the above, plus x10 Pilot-RC servos, all pre-installed. Just add your own turbine of choice.
Required hardware:
Turbine size:
- 120-200N for normal sport flying
- 200-240N for 3D vector flight – Avoid high speed, high G flying
Servos: Total x10 (x7 standard size + x3 medium size)
x7 standard size high torque
x2 for flaps (minimum 40kg) x1 for rudder (minimum 40kg)
x2 for elevators (minimum 28kg) x2 for vector rudder/elevator (minimum 28kg)
x3 medium size servo (size: 35x15x30mm)
x2 for ailerons (minimum 16kg)
x1 for steering (minimum 16kg)
Also requires all the usual accessories such as transmitter, receiver, batteries, powerbox and possibly other small accessories.
Pilot-Rc recommended hardware:
- Servos: Pilot-Rc PW48AH for flaps and rudder and vector and elevator
- Servos: Pilot-Rc PW21AH for ailerons , steering
- Servo arms: Pilot-Rc 1.6″, 1,2″ and 0,8″ Aluminium arms (included with Pilot-Rc servos)
Pilot-Rc recommended ACCESSORIES:
- Pilot-RC Wingbags (2.7m FC1)
- Pilot-RC Fuselage bag (2.7m FC1)
Colour schemes available:
Scheme 07 – Red-Pearl blue
Scheme 08 – Green Kawasaki Pearl Blue
Scheme 09 – yellow pearl blue
CONTROL THROWS:
- Flap: Maximum available
- Aileron: 15mm up / 15mm down (measured at the wing tip)
- Rudder: 43mm left / 43mm right
- Elevator: 38mm up / 38mm down (measured from the tip at trailing edge of the elevator)
*Please note that the correct “center” position for the elevator is not when it is level
CENTER OF GRAVITY:
soon…… back from the leading edge of the wing at the fuselage
Measured with fuel bag, landing gear down.
VECTOR AND GYRO:
Elster Jet recommend the use of the gyro systems by Powerbox-Systems. These offer two banks, each with individually programmable settings.
| FUNCTION | NORMAL FLYING | 3D FLYING |
| Aileron | Normal Gain 20% | Normal Gain 40% |
| Elevator | Normal Gain 15% | Normal Gain 45% |
| Vector Elevator | Off | Normal Gain 90% |
| Vector Rudder | Off | Normal Gain 90% |
FULL Build manual:
Coming soon!